Last Updated: November 18, 2026
Quick Summary
The subpanel installation cost depends on four things: amperage, distance from the main panel, site conditions, and permit requirements, so no two homes price out the same. Every quote should break into four lines: labor, materials, permit fees, and feeder length. Labor is usually the largest single line, and feeder length is the most variable.
- Subpanels are commonly sized at 60, 100, or 125 amps, with heavier feeder wire as amperage climbs.
- Labor typically makes up 40 to 55 percent of a subpanel quote.
- Permit fees are set by your local building department and are usually flat per panel.
- A detached garage job costs more due to long feeder runs, trenching, and separate grounding.
- A load calculation confirms your main service panel can handle the added subpanel.
Table of Contents
- What Drives the Cost of Installing a New Electrical Subpanel
- Itemized Cost Breakdown: Labor, Materials, Permits, and Feeder Length
- 100 Amp Subpanel Installation Cost and Smaller Panel Options
- Electrician Cost to Install a Subpanel and How Labor Is Priced
- Cost to Install a Subpanel in a Detached Garage
- Using an Electrical Subpanel Installation Calculator Without Getting Burned
- Checking Whether Your Main Service Panel Has the Capacity
- Permits, Inspection, and Code Compliance Before You Hire
- Frequently Asked Questions
What Drives the Cost of Installing a New Electrical Subpanel
The cost of installing a new electrical subpanel depends on four things: amperage, distance from the main panel, site conditions, and permit requirements. No two homes price out the same, which is why any flat quote you see online should be treated as a starting point, not a final number.
A subpanel is a small panel with its own breakers, fed from your main service panel. It exists to shorten wire runs and free up space in a panel that is already full.
Amperage and Breaker Capacity
Amperage sets the floor for everything else. A 60-amp feeder uses smaller wire and a smaller panel than a 100-amp feeder, and both cost less than a 200-amp setup. Subpanels are commonly sized at 60, 100, or 125 amps.
Breaker capacity matters just as much. If you are adding a subpanel for a hot tub, an EV charger, or a garage workshop, count the breaker spaces you need now and add a few spare. A panel that is full on day one was the wrong panel.
Distance, Wire Run, and Site Conditions
Distance is the quiet cost driver. Copper feeder wire is priced by the foot, and the gauge you need climbs with amperage. A short run through an open basement is a different job from a long run through finished walls or underground conduit to a detached garage.
Site conditions decide labor time. Finished drywall, cramped crawlspaces, and concrete that needs cutting all add hours. An unfinished basement with open joists is the easiest version of this job.
Itemized Cost Breakdown: Labor, Materials, Permits, and Feeder Length
Every subpanel quote should break into four lines: labor, materials, permit fees, and feeder length. If a quote is one lump sum with no breakdown, ask for the itemization before you sign. The table below shows how each line typically behaves for a 100-amp subpanel installed 25 feet from the main panel in an unfinished basement, the simplest realistic version of this job.
| Cost Line | Typical Share of Total | What Drives It |
|---|---|---|
| Labor | 40-55% | Panel mounting, breaker installation, wire pulling, termination, and inspection coordination |
| Materials (panel, breakers, ground bar, connectors) | 15-25% | Panel amperage rating, number of breaker spaces, brand, and whether a ground bar is included |
| Feeder wire and conduit | 15-30% | Wire gauge (ampacity), run length, and whether conduit is required |
| Permit and inspection fees | 5-15% | Local building department fee schedule, usually flat per panel regardless of amperage |
Typical Share of Total
Here is how each line behaves in practice:
- Labor: priced by job complexity or hourly rate. A panel swap in open space with exposed joists moves fast. Fishing wire through finished walls, cutting and patching drywall, or trenching for underground conduit does not. Most practitioners find labor is the line that varies most between quotes for the same visible scope, because it absorbs the hidden difficulty of the wire route.
- Materials: the subpanel itself, feeder cable or individual conductors, conduit and fittings, a ground bar, breakers, and connectors. A 100-amp panel with 12 breaker spaces costs more than a 60-amp panel with 6 spaces, but the difference is usually smaller than the difference in feeder wire cost. Do not let a quote hide a cheap panel behind an expensive labor line.
- Permits: set by your local building department, not by the electrician. Fees vary by jurisdiction and are typically a flat fee per panel, so they do not scale with amperage. Ask for the permit fee as a separate line so you can verify it against your jurisdiction’s published fee schedule.
- Feeder length: the single most variable line. Wire cost scales directly with the run, and the gauge you need climbs with amperage. A 25-foot run of 6-gauge copper feeder is a different number from a 75-foot run of 2-gauge copper feeder. Ask the electrician to state the feeder length and wire gauge on the quote so you can compare bids on the same basis.
We quote subpanel work flat-rate, and you approve the number first. When you compare quotes, put them side by side on these four lines, a quote that is $400 lower on labor but $600 higher on materials is not actually cheaper, and a quote that omits the permit fee is not a complete bid.
100 Amp Subpanel Installation Cost and Smaller Panel Options
The 100 amp subpanel installation cost runs higher than a 60-amp job because the feeder wire is heavier and the panel itself is larger, but it leaves room for future circuits.
Smaller options fit smaller jobs:
- 60-amp subpanel: best for a single large load, like a hot tub or a small detached shed.
- 100-amp subpanel: best for garages, workshops, and additions with multiple circuits.
- 125-amp subpanel: best when you expect to add an EV charger later.
| Panel Size | Best For | Feeder Wire | Relative Cost |
|---|---|---|---|
| 60 amp | Hot tub, small shed | Lighter gauge | Lowest |
| 100 amp | Garage, workshop | Heavier gauge | Middle |
| 125 amp | Future EV charger | Heaviest gauge | Highest |
Best for: homeowners adding one or two new circuits.
Skip if: your main panel cannot spare the capacity. Check that first.
Electrician Cost to Install a Subpanel and How Labor Is Priced
The electrician cost to install a subpanel is usually the largest single line on the quote, and it is the line homeowners understand least.

Flat-rate pricing sets the number before work begins. Our flat-rate pricing is set before work begins.
A load calculation on your existing service is an important step before pricing subpanel work.
If you are in Kennewick and want the labor priced up front, our licensed electricians for panels and breakers can be contacted for a flat-rate quote.
Cost to Install a Subpanel in a Detached Garage
The cost to install a subpanel in a detached garage is higher than an attached-garage job, and distance explains almost all of it. Detached garages usually need a long feeder run, often underground in conduit, plus a separate grounding and bonding setup at the outbuilding.
| Scenario | Feeder Route | Typical Added Cost vs. Attached Garage | Main Cost Drivers |
|---|---|---|---|
| 60-amp panel, garage 20 feet from house, direct-burial feeder | Short underground run, no trenching through obstacles | Lowest premium | Shorter wire run, smaller panel, one ground rod |
| 100-amp panel, garage 60 feet from house, conduit in trench | Long underground run with conduit, possible driveway or patio crossing | Highest premium | Longer wire run, heavier gauge, trenching labor, conduit, grounding electrode system |
Three things push this job up:
- Trenching: underground conduit means digging, and that is labor, not materials. Burial depth for residential feeder conduit is set by the National Electrical Code and by local amendments, and the required depth depends on whether the conduit is metal, PVC, or direct-burial cable. A trench that crosses a driveway or patio costs more because the surface has to be cut and restored. Ask the electrician to state the burial depth and conduit type on the quote.
- Grounding and bonding: a detached structure with a subpanel needs a grounding electrode system at the outbuilding, typically a ground rod, plus a separate ground bar in the subpanel and a bonding jumper to the equipment grounding conductor. The neutral bar and ground bar must be separated in the subpanel, just as they are in the main panel. This is a code requirement, not an upgrade, and a quote that omits it is incomplete.
- Weatherproofing: conduit, fittings, and burial depth all have requirements. Above-ground conduit on the exterior of the garage needs to be rated for wet locations, and any penetration through the garage wall needs to be sealed. These are small line items individually but add up on a long exterior run.
A short direct run from a house panel to a garage wall is the cheap version. A long buried run to a garage at the back of the lot is the expensive one. Same panel, very different job.
Using an Electrical Subpanel Installation Calculator Without Getting Burned
An electrical subpanel installation calculator is a useful sanity check and a terrible final answer. Online calculators estimate from averages: average wire cost, average labor, average distance. Your house is not average.
Use a calculator to get a rough idea before you call anyone. Then ask a licensed electrician for a real number based on your actual run, your actual panel, and your actual permit fees.
The calculator’s real job is helping you spot an outlier quote. It cannot see your walls.
Checking Whether Your Main Service Panel Has the Capacity
Capacity is the question that decides whether a subpanel is even possible. A subpanel does not create power. It splits what your main service panel already delivers.
A licensed electrician checks capacity with a load calculation, adding up the existing demand and comparing it to your service rating.
If you want to understand what a capacity shortfall looks like before you call, our guide to the signs you need an electrical panel upgrade walks through the warning signs. For the full picture on options and what an upgrade involves, see our electrical panel upgrade services guide.
Watch out: adding a subpanel to a maxed-out main panel is the most common mistake we see. It works fine until the day everything runs at once.
Permits, Inspection, and Code Compliance Before You Hire
Permits and inspection are not optional, and they are not paperwork theater.
A common mistake is hiring on price alone and skipping the permit. Unpermitted work can complicate a home sale and may void insurance coverage on the affected circuits.
Before you hire, check three things: a current license, proof of insurance, and a written scope that names the permit. Our guide to choosing a licensed electrician covers the questions to ask. If you are ready to move, you can request a free panel assessment with permits and financing handled for you.
A subpanel done wrong creates problems: nuisance trips, failed inspections, and a bill that grows after the fact. AllSet Home offers flat-rate pricing with licensed, background-checked technicians and 24/7 emergency response.
Frequently Asked Questions
How much do electricians charge to install a subpanel?
Electricians usually bill subpanel work either hourly or as a flat rate, and the total depends on amperage, feeder length, and whether the panel goes in an attached wall or a detached garage. Labor is only part of the bill: feeder cable, conduit, breakers, and the permit add to it. Because every house is wired differently, ask for a written, itemized quote that separates labor from materials so you can see what you are paying for.
Does installing a subpanel require a permit?
In most jurisdictions, yes. Adding a subpanel creates new circuits and changes the load on your service, so local building departments typically require an electrical permit and a follow-up inspection. Skipping the permit can complicate insurance claims and resale inspections later. Ask your electrician who pulls the permit and whether the fee is included in the quote, since permit costs vary by municipality and are often billed separately.
Can you run a 100 amp subpanel off a 100 amp service?
Technically it is a bad idea. A 100 amp subpanel fed from a 100 amp main service leaves no capacity for the rest of the house, and a load calculation will usually show the service cannot support it. Have a licensed electrician run a load calculation on your existing panel before committing to any subpanel size.
How much does it cost to install a subpanel in a detached garage?
A detached garage costs more than an attached one because the feeder has to run underground or overhead across the yard, which means trenching, conduit, and more wire. The farther the garage sits from the main panel, the higher the material and labor cost. Get a quote that lists the feeder length, conduit type, and trenching responsibility separately so there are no surprises once digging starts.



